Home

Portfolio

All projects

Design, analysis, and fabrication work from Carleton University, RIT STEP research, and PLTW coursework.

CATIA isometric view of the ping-pong launcher assembly: a funnel bucket on a stand feeding a ramp, two flywheels on motors at the end of the ramp, and a net, all mounted on a square base plate
01 Design and Build 2026

Ping-Pong Ball Launcher

An Arduino-timed flywheel launcher that fed and fired 20 ping-pong balls in 26.5 seconds.

Open case study
CATIA rendering of the assembled aircraft model, with fuselage, nose, wings, cabin windows, and tail
02 CAD & Technical Drawing 2025

Aircraft CAD Model in CATIA

Each aircraft part modeled individually in CATIA from specifications, then assembled into the full aircraft.

Open case study
Truss internal force diagram for the light rail bridge: a Warren truss between a pin support at A and a roller support at I prime, with the axial force in every member labeled in kN, tension in blue and compression in red
03 Structural Analysis 2025

Bridge Truss Design and Analysis

Force analysis and member sizing for a 40.9 m light rail bridge truss, ending in a Warren configuration.

Open case study
Research poster titled Designing Next-generation Electrolytes for Solid Oxide Fuel Cells, showing the derived lattice-strain equation, a Desmos graph used to find optimal column counts, and computational structures of CeO2/SrTiO3 and BaZrO3/MgO interfaces
04 Computational Materials 2023-2024

Designing Next-Generation Electrolytes for Solid Oxide Fuel Cells

A mathematical model for choosing column counts that reduced fuel-cell electrolyte lattice strain from 27.82% to 3.76%.

Open case study
Floating desalination prototype in a test pool: an inverted clear umbrella frame with taped film panels, a small solar panel mounted at the center mast, and the red 3D-printed electrolysis chamber visible beneath the film
05 Renewable Energy Systems 2022-2023

Solar Desalination and Hydrogen Electrolysis System

A floating solar device built to desalinate salt water and generate hydrogen; the redesigned chamber produced hydrogen 8.7 times faster.

Open case study
Side view of the finished trailer-mounted greenhouse in a parking lot: two solar panels on the sloped roof, large windows, and the 400 W wind turbine on a mast behind it
06 Renewable Energy Systems 2023

Mobile Sustainable Greenhouse

A trailer-mounted off-grid greenhouse powered by a student-built 960 W solar array.

Open case study
Assembled VEX marble sorter on a classroom desk, with the funnel, light-sensor station, servo-driven diverter, and clear collection cup visible against a classroom bulletin board
07 Mechatronics 2022

Automated Marble Sorting System

A sensor-driven VEX machine that sorts marbles by transparency, fully autonomously.

Open case study
The final prototype: a light blue 3D-printed box on a countertop with a square camera window on the front, a sensor board on the side, and a cable exiting the top
08 Embedded Systems 2020-2021

Self-Sufficient Early Warning Fire System

A Raspberry Pi wildfire detector with camera and sensors, built and tested against a campfire in grade 9.

Open case study
Hand-drawn schematic of the air conditioning cycle from my lab notebook: condenser, expansion valve, evaporator, and compressor in a loop with numbered state points, plus closer looks at each component with heat and work arrows
09 Thermo-Fluid Systems 2026

Vapor-Compression Cycle Analysis of a Residential Air Conditioner

Measured a real air-conditioning system at six state points and closed the energy balance on its refrigeration cycle.

Open case study
Photograph of the laboratory flow bench: a closed water loop on a bench frame with the five inline flow meters, gauges, and a reservoir jug
10 Fluid Mechanics 2026

Uncertainty Analysis of Five Flow-Measurement Devices

Compared five flow meters against a reference measurement and ranked them by total uncertainty.

Open case study
Optical micrograph of an etched carbon steel sample showing light ferrite grains and dark pearlite regions
11 Materials Engineering 2026

Metallography: Identifying an Unknown Steel by Its Microstructure

Prepared steel samples for the microscope and identified an unknown one from its microstructure.

Open case study
Diagram from the report of the Sun, Earth, and a satellite on the equatorial plane, showing the geometry used to work out when the satellite is in Earth's shadow
12 Systems Research Report 2026

Satellite-Based Weather Forecasting With Machine Learning

A team report on how orbits, sensors, radar, ML, and solar power combine for weather forecasting.

Open case study